DS2740U+T&R【PDF 11/16 页】IC CURRENT GAUGE(15BIT) 8UMAX

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录40

7页 8页 9页 10页 [11页]12页 13页 14页 15页

DS2740

Skip Net Address [CCh]. This command saves time when there is only one DS2740 on the bus by

allowing the bus master to issue a function command without specifying the address of the slave. If more

than one slave device is present on the bus, a subsequent function command can cause a data collision

when all slaves transmit data at the same time.

Search Net Address [F0h]. This command allows the bus master to use a process of elimination to

identify the 1-Wire net addresses of all slave devices on the bus. The search process involves the

repetition of a simple three-step routine: read a bit, read the complement of the bit, then write the desired

value of that bit. The bus master performs this simple three-step routine on each bit location of the net

address. After one complete pass through all 64 bits, the bus master knows the address of one device. The

remaining devices can then be identified on additional iterations of the process. See Chapter 5 of the Book

of DS19xx i

Button

?/DIV>

Standards for a comprehensive discussion of a net address search, including an actual

example. (This publication can be found on the Maxim/Dallas Semiconductor website at www.maxim-

ic.com.)

Resume [A5h]. This command increases data throughput in multidrop environments where the DS2740

needs to be accessed several times. Resume is similar to the Skip Net Address command in that the 64-

bit net address does not have to be transmitted each time the DS2740 is accessed. After successfully

executing a Match Net Address command or Search Net Address command, an internal flag is set in the

DS2740. When the flag is set, the DS2740 can be repeatedly accessed through the Resume command

function. Accessing another device on the bus clears the flag, thus preventing two or more devices from

simultaneously responding to the Resume command function.

FUNCTION COMMANDS

After successfully completing one of the net address commands, the bus master can access the features of

the DS2740 with any of the function commands described in the following paragraphs and summarized in

Table 4. The name of each function is followed by the 8-bit opcode for that command in square brackets.

Read Data [69h, XX]. This command reads data from the DS2740 starting at memory address XX. The

LSb of the data in address XX is available to be read immediately after the MSb of the address has been

entered. Because the address is automatically incremented after the MSb of each byte is received, the LSb

of the data at address XX + 1 is available to be read immediately after the MSb of the data at address XX.

If the bus master continues to read beyond address FFh, the DS2740 starts over at address 00h.

Addresses labeled Reserved in the memory map contain undefined data. The Read Data command can

be terminated by the bus master with a reset pulse at any bit boundary.

Write Data [6Ch, XX]. This command writes data to the DS2740 starting at memory address XX. The

LSb of the data to be stored at address XX can be written immediately after the MSb of address has been

entered. Because the address is automatically incremented after the MSb of each byte is written, the LSb

to be stored at address XX + 1 can be written immediately after the MSb to be stored at address XX. If

the bus master continues to write beyond address FFh, the DS2740 starts over writing at address 00h.

Writes to read-only addresses and reserved addresses are ignored. Incomplete bytes are not written. See

the Memory section for more details.

Button is a registered trademark of Dallas Semiconductor.

11 of 16

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式